obd2 Volkswagen, Audi cars with the special operations 1552

 Now common in our VW / Audi models are:
Santana, GLi, Gsi, Jetta, Jetta avant-garde, Audi 100,200, V6, Passat B4, B5, Audi A6, Bora, Polo, and FAW Red Flag, etc. With the development of EFI technology, these cars are more and more electronic control system.
from the early engine system, transmission system, ABS, air conditioning, anti-theft system, an increase of airbags, central door lock, speaker, instrument cluster, radio, heated parking, drivers seat adjustment system, while special equipment required to use more and more.
Here to gold as an example of the Pentium IIS Chinese 1552 VW / Audi cars special function operation hope it'll help in the maintenance time.
First, the basic throttle setting 1, setting the content; in turn the ignition switch, throttle control unit can be carried out and the engine control unit adaptation.
2, the basic setup process:
further throttle the basic settings, throttle response regulator into the position of running the largest to the smallest position, the engine control unit to learning through adaptive throttle position control unit only and throttle potentiometer sensor and throttle controller comparison curves.
3, under the circumstances must be adaptive:
removable power interruption control unit replacement throttle control unit changes the engine throttle changes the engine control unit 4, the basic set conditions:
fault no fault memory 11.5V battery voltage is not less than all the electrical appliances should be turned off idle throttle position 5, the basic setup methods and steps:
1) Turn the ignition switch does not start the engine.
2) Connect the 1552 Golden Pentium IIS-Chinese automotive diagnostic menu (Figure 1-1) Press the OK button to enter the system menu (Figure 1-2).
3) Select the OK button to enter the engine system according to the function menu (Figure 1-3) 4) Select the basic adjustment to adjust the input group number (Figure 1-4).

1 Language 3 → 2 car diagnostic test re-read history of failure 4 System 2 → 1 engine braking system transmission system 3 4 → 5 basic adjustment of air-conditioning system reads the data stream 6 7 8 separate data channel coding control unit Enter group number
adjusted exit 0 00 □ □ □ ↑ ↓ determined Figure 1-2 Figure 1-3 Figure 1-1 Figure 1-4 Note:
common models adjusted group number (Table 1-1) < br> 001 small red flag, Passat B4, Audi 100,200 098 Santana GSI, Passat B5 (1.
8), Jetta (5 valve), Audi A6, V6 060 Jetta avant-garde (2 valves) , A6 (1.8 2.4 2.8), B5 (1.8T 2.8), BORA, PALO
Table 1-15) Click the OK button after the setting process, the throttle controller through the MIN to MAX points and five between positions, obd2.
throttle control unit to the corresponding point stored in memory, vag com cable, this process takes about 10 seconds, followed by a short in the starting throttle position, and then close the gold Pentium IIS-1552 screen display as shown in Table 1 - 2, Figure 1-5 Figure 1-3
group number display shows the contents of 098 or 060 position of the basic adjustment XX Group 12341, throttle potentiometer voltage 2, throttle positioning voltage of 3, 4, work status, match status ADP.lauft (normal match) ADP.ok (Match completed) ADP ERROR (matching error)
Table 1-26) when the screen display 4 shows ADP.OK (or ADP.io) when the basic setup is complete (Figure 1-6), press the launch button to complete the setup.
7) If the basic set interrupt control unit, or error, may be due to the following reasons ● throttle idle stop point is not reached.
such as carbon or not to adjust the throttle zipper ● ● Battery low voltage wire throttle control unit or damaged cards ● ● Throttle committed to start the adaptive process of the engine, or step on the accelerator pedal.
fault storage after interruption failure 17967 or 17973 to store the next time the ignition switch automatically re-open the basic settings.

adjustment adjustment XXX XXX Group 1234 Group X. XXXV X.XXXV-ADPO.K 8 9 adaptive coding control unit 11 matches the set of 10 service stations login code
input channel number 0 0 □ Quit □ □ ↑ ↓ identified in Figure 1-5 Figure 1-6 Figure 1-7 Figure 1-8 with:
Jetta avant-garde (b valve) model of the throttle basic settings:
Description:
Jetta avant-garde model is used in the production of Siemens 2v-Mp1 EFI engine and multi-point fuel injection ignition system, which models the basic throttle settings during the first adaptive be removed to clear the previous adaptive value, to conduct basic adjustments.
basic methods and procedures set:
choice in menu Figure 1-7 Adaptive matching ② Press the OK button input channel number 00, press the OK button.
(Figure 1-8) ③ whether to clear the screen of known values ​​(Figure 1-9) Press the OK button ④ screen new study has been completed (Figure 1-10), can bus.
press the Escape key to complete the adaptive clear ⑤ continue to throttle the previous 5 steps to complete the basic settings (Note:
Jetta car avant-garde group number of basic adjustments for the 060)
whether to clear out the known values ​​□ □ The new study has been completed to determine out Figure 1-9 Figure 1-10 □ automotive diagnostic vehicle diagnosis without disintegration (or just remove the individual parts) of the conditions, determine the status of automotive technology, to identify the cause of fault location and check the.